Reformer Standing Splits
What are standing splits on the Reformer, and how does the carriage assist deep flexibility?
The Reformer Standing Splits is a advanced-level pilates movement that primarily targets the hamstrings, hip flexors. It uses reformer as the primary implement and engages the core, glutes as secondary movers. In this guide you'll find a complete breakdown — anatomy, step-by-step setup, execution, coaching cues, common mistakes, programming recommendations, regressions, progressions, warm-up, cool-down, safety notes, and FAQs.
How to perform
-
1
Set up your reformer with a weight that allows clean form for 3–6 reps.
-
2
Position your body so the hamstrings, hip flexors is the primary mover — brace your core before each rep.
-
3
Stack your joints — wrists under elbows, elbows under shoulders, feet hip-width for stability.
-
4
Establish a neutral spine, draw your ribs down, and breathe in to brace.
-
5
Initiate the movement with intent — control the eccentric, explode on the concentric.
Execution
-
1
Inhale and brace your core — 360° pressure into the belt line.
-
2
Lower under control (controlled tempo) — keep tension on the target muscle.
-
3
Pause for a beat at the bottom of the range without losing brace.
-
4
Drive through the target muscle group, exhaling on the concentric.
-
5
Lock out cleanly without hyperextending — reset and brace for the next rep.
- ▸ Brace 360° around your core before every rep — never lift on a soft midsection.
- ▸ Drive through the hamstrings, hip flexors as the primary mover, not the joints.
- ▸ Control the eccentric for 2–3 seconds — this is where most pilates growth happens.
- ▸ Train the longest range you can control safely — partial reps build partial strength.
- ▸ Leave 1 reps in reserve on most working sets — autoregulate when life hits hard.
- ✕ Loading the bar too heavy before owning the technique at submaximal weights.
- ✕ Cutting the range of motion short to move more weight than you can actually control.
- ✕ Letting momentum take over — bouncing, jerking, or losing brace at the bottom.
- ✕ Skipping the warm-up sets and jumping straight to working weight.
Periodisation note: Run this exercise for 4–6 weeks, then change the variation or progression. Add load when the top set feels RPE 6 — never chase numbers at the cost of form.
- Reduce load by 20–30% and slow the tempo to 4-1-2-1.
- Switch to a more stable variation: machine or supported version of the reformer standing splits.
- Reduce range of motion to the pain-free portion and gradually re-expand over weeks.
- Add 2.5–5% load weekly while keeping RPE 7 on the top set.
- Increase range of motion with deficit or pause variations once you own the standard reformer standing splits.
- Add a tempo or pause at the hardest position to increase time under tension.
- Tempo reformer standing splits (4-2-1-0)
- Paused reformer standing splits at the sticking point
- Deficit reformer standing splits (increased range)
- Banded reformer standing splits (accommodating resistance)
- 5 min easy aerobic work to raise tissue temperature.
- Dynamic mobility for breathing, pelvic tilts, light articulation.
- 2 specific warm-up sets of the reformer standing splits at 50% and 75% of working weight.
- 5 min easy aerobic cool-down.
- Static stretching: spinal twist, child's pose, hip flexor stretch.
- Breath work — 4–7–8 breathing for 5 rounds to downregulate.
- Get cleared by a physio if you have acute spinal pathology, osteoporosis with flexion caution.
- Always use a spotter or safety pins for barbell work near 1RM loads.
- Check equipment integrity — bar collars, bench stability, clips on bands.
- Stop if you feel sharp pain in a joint. Muscle burn is fine; joint pain is not.
- Primary developer of the hamstrings, hip flexors.
- Reinforces the pilates pattern used in daily life and sport.
- Builds strength and stability in the pilates musculature.
- Improves movement competency under load.
- Foundational movement for almost every structured training program.
- Anyone with acute acute spinal pathology, osteoporosis with flexion caution.
- Beginners who haven't earned the right to load the pattern yet.
- Anyone returning to training after surgery without physio clearance.
- Barbell — highest load potential, requires good mobility and stability.
- Dumbbells — greater range, less stable, good for asymmetry correction.
- Bands or machine — lower joint stress, great for rehab or burnout sets.
Research on pilates movements consistently shows the hamstrings, hip flexors as the primary mover, with meaningful activation of the core, glutes. Time under tension in the 3–6 rep range with 2–3 min rest is the sweet spot for both strength and hypertrophy adaptations.
Frequently asked questions
How often should I do the reformer standing splits?
1x/week (heavy) is a good starting point. Advanced lifters can hit pilates 2x/week with at least 48h recovery between sessions.
Is the reformer standing splits good for beginners?
Yes, if the load is conservative and technique is coached. Start with the regression listed above and progress from there.
What weight should I use for the reformer standing splits?
Pick a weight that lets you complete the target reps with RPE 7–8 — that means 3–6 reps with 1–2 left in the tank. Add 2.5% when it feels easy.
Can I do the reformer standing splits at home?
Yes, if you have the equipment. If not, see the equipment alternatives below for bodyweight or band-based substitutes that hit the same muscles.